Encapsulation carpet cleaning and commercial carpet care forum by Excellent-Supply.com & Releasit   ›   Forum Home   ›   GENERAL DISCUSSION   ›   Frustrating Cimex Repair

  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Frustrating Cimex Repair
Cosway_Toronto
JUNIOR ENCAPPER
**

Joined: Jan 2013
Posts: 16

Thanks: 8
Given 0 thank(s) in 0 post(s)
#1
10-05-2017, 01:46 PM
These suckers won't budge! Any suggestions?
thanks


Attached Files Image(s)
   
  Find
  Reply
Cosway_Toronto
JUNIOR ENCAPPER
**

Joined: Jan 2013
Posts: 16

Thanks: 8
Given 0 thank(s) in 0 post(s)
#2
10-05-2017, 01:48 PM
I want them off so I can install new bearings. So to be clear, they do spin but we just can get them off Smile
  Find
  Reply
lee@deepclean.us.com
ENCAP HEAVYWEIGHT
*****

Joined: Oct 2012
Posts: 326

Thanks: 0
Given 52 thank(s) in 51 post(s)
#3
10-05-2017, 02:47 PM
Call Rodney at Excellent. I am sure he can help you!
  Find
  Reply
LemuelDansie
JUNIOR ENCAPPER
**

Joined: Oct 2017
Posts: 1

Thanks: 0
Given 1 thank(s) in 1 post(s)
#4
10-06-2017, 04:36 AM
Call a Expert guy who can definitely help you!
  Website   Find
  Reply   Purge Spammer
encaprodney
Encap Tech
***

Joined: Jul 2012
Posts: 85

Thanks: 0
Given 12 thank(s) in 11 post(s)
#5
10-06-2017, 10:21 AM
Yes, some can be very stubborn Angry  and I have had some on so tight that the brush pulley gets bent out of shape and needs replaced. Use Lots of heat on that center brass spindle and protect the threads and spout of that brass spindle as you clamp down on that pulley. 
Call me at the office if you need more technical assistance.
Rod Clarkin
Excellent Supply 727-821-2020 
  Find
  Reply
Cosway_Toronto
JUNIOR ENCAPPER
**

Joined: Jan 2013
Posts: 16

Thanks: 8
Given 0 thank(s) in 0 post(s)
#6
10-24-2017, 12:36 PM
how easy should this pop off?  Angry Sad Dodgy


Attached Files Image(s)
   
  Find
  Reply
Cosway_Toronto
JUNIOR ENCAPPER
**

Joined: Jan 2013
Posts: 16

Thanks: 8
Given 0 thank(s) in 0 post(s)
#7
10-24-2017, 12:38 PM
not giving up


Attached Files Image(s)
   
  Find
  Reply
Cosway_Toronto
JUNIOR ENCAPPER
**

Joined: Jan 2013
Posts: 16

Thanks: 8
Given 0 thank(s) in 0 post(s)
#8
10-24-2017, 12:39 PM
Sad grrrrrrrrrrrr


Attached Files Image(s)
   
  Find
  Reply
encaprodney
Encap Tech
***

Joined: Jul 2012
Posts: 85

Thanks: 0
Given 12 thank(s) in 11 post(s)
#9
10-25-2017, 10:20 AM (This post was last modified: 10-25-2017, 10:21 AM by encaprodney.)
I feel your pain! I have tried a number of methods and finally came up with this one that really works....We use this beefy puller for that stubborn center pulley. Use lots of heat to help free it up and protect those center motor shaft threads by  screwing the center bolt back in without the washer so when you crank down on that puller bolt, it doesn't damage the threads. Feel free to call me at the office if you need any more assistance. 

Here is a link to a comparable puller that you can purchase for that task.

https://www.homedepot.com/p/Powerbuilt-Power-Steering-Pulley-Puller-648460/203120575?cm_mmc=Shopping%7CVF%7CG%7C0%7CG-VF-PLA%7C&gclid=EAIaIQobChMIqqHwqfuL1wIVQ0SGCh3aoAQaEAYYBSABEgI-OvD_BwE&gclsrc=aw.ds&dclid=CO2Qx677i9cCFQvZwAodTI0DAg
Rod Clarkin
Excellent Supply 727-821-2020 
  Find
  Reply




Users browsing this thread: 1 Guest(s)