10-24-2013, 02:41 PM
Hello All
Been lurking for a while but first time posting. Somewhat new to carpet cleaning and the encamp/padcap process, but have a few jobs here and there. I previously used carpet cleaning as more of a side job, but now am wanting to move more full-time with it, both commercial and residential.
I currently have a dual-speed 17-inch buffer with a tank, a BrushPro 17 and an Oreck Orbiter. I also purchased the CMS but have yet to have the chance to utilize it. I will be starting to create my website this week (wordpress) and learn as I go on that. I also got one sample each of Hydrox, Punch and DS2. I'm looking to get get feedback, advice, tips & tricks, suggestions, shortcuts, etc. on about anything you guys are willing to offer.
One question I have is about process and suggestions for the equipment I have. A process that I've read on here is as follows:
1. Vacuum 2. Prespray 3. Let dwell for 10-15 4. Work in with CRB 5. Padcap
Someone else had a similar process, but slightly different:
1. Vacuum 2. Prespray 3. Work in with CRB 4. Let dwell for 10-15 5. Padcap
Does it make a difference if I work the pre spray in right away with a CRB, or let dwell prior to working with a CRB?
Also, I have to residential jobs coming up next week and would invite any info/suggestions regarding products, process, etc.
Job 1
Room in basement: Tan with green specs Twist/Frieze type carpet. An area about 4x4 has dark stains/discoloration. This is where they come in from the garage and take off snow boots, etc. after walking across 4 feet of tile.
Living Room and Toy Room: Light Tan cut pile. Dirty but not ridiculous. Some spots from juice, etc. and a bit coffee spill from about 2 weeks ago.
Family Room/Steps/Hall: Dark Hunter Green cut pile. No visible stains or damage.
Job 2
All Light Tan bordering on white cut pile. Not bad at all. Some traffic lanes and that's about it.
Any information, suggestions, products to use, process, etc. considering the equipment I have would be great! Depending on what feedback I get, I may be ordering some products by tomorrow. Sorry this first post is so long.
Thanks guys, and I look forward to being a contributor on this board and also getting some great advice.
Steve
Been lurking for a while but first time posting. Somewhat new to carpet cleaning and the encamp/padcap process, but have a few jobs here and there. I previously used carpet cleaning as more of a side job, but now am wanting to move more full-time with it, both commercial and residential.
I currently have a dual-speed 17-inch buffer with a tank, a BrushPro 17 and an Oreck Orbiter. I also purchased the CMS but have yet to have the chance to utilize it. I will be starting to create my website this week (wordpress) and learn as I go on that. I also got one sample each of Hydrox, Punch and DS2. I'm looking to get get feedback, advice, tips & tricks, suggestions, shortcuts, etc. on about anything you guys are willing to offer.
One question I have is about process and suggestions for the equipment I have. A process that I've read on here is as follows:
1. Vacuum 2. Prespray 3. Let dwell for 10-15 4. Work in with CRB 5. Padcap
Someone else had a similar process, but slightly different:
1. Vacuum 2. Prespray 3. Work in with CRB 4. Let dwell for 10-15 5. Padcap
Does it make a difference if I work the pre spray in right away with a CRB, or let dwell prior to working with a CRB?
Also, I have to residential jobs coming up next week and would invite any info/suggestions regarding products, process, etc.
Job 1
Room in basement: Tan with green specs Twist/Frieze type carpet. An area about 4x4 has dark stains/discoloration. This is where they come in from the garage and take off snow boots, etc. after walking across 4 feet of tile.
Living Room and Toy Room: Light Tan cut pile. Dirty but not ridiculous. Some spots from juice, etc. and a bit coffee spill from about 2 weeks ago.
Family Room/Steps/Hall: Dark Hunter Green cut pile. No visible stains or damage.
Job 2
All Light Tan bordering on white cut pile. Not bad at all. Some traffic lanes and that's about it.
Any information, suggestions, products to use, process, etc. considering the equipment I have would be great! Depending on what feedback I get, I may be ordering some products by tomorrow. Sorry this first post is so long.
Thanks guys, and I look forward to being a contributor on this board and also getting some great advice.
Steve